ENGINE AND TRACTOR SPECIFICATIONS |
Bore and Stroke (In.) |
4 x 4 |
Displacement (Cu. In) |
100.5 |
Compression Ration |
6.5:1 |
Compression Pressure (Est.) |
125 |
Rated RPM |
1850 |
Idle RPM (Fast) |
2025 +/- 25 |
Power Shaft RPM (At Rated Load) |
560 |
Belt Speed (Ft./Min.) |
3000 |
H.P. 100% Max Belt (Maximum belt hp corrected to
sea level and 60 deg. F. air temp) |
40 T |
25.23 |
40 S |
24.86 |
40 C |
24.99 |
Shipping Weight (Lbs.) |
40 T (with 9-34, 5.00x15 tires) |
3000 |
40 S (with 9-24, 5.00x15 tires) |
2750 |
40 U (with 10-24, 5.00x15 tires) |
2850 |
40 W (with 10-34, 6.00x16 tires) |
3000 |
40 V (with 11-34, 5.00x15 tires) |
3050 |
40 H (with 10-38, 6.50x16 tires) |
3400 |
40 C (with 12" shoes) |
3-Roller - 4000
4-Roller - 4125
5-Roller - 4560 |
Spark Advance |
25 degrees |
Pulley Face (In.) |
6 |
Rings per Piston |
4 |
Distributor Automatic Advance |
15 degrees |
CAPACITIES |
Fuel Tank (Gal.) |
10.5 |
Starting Tank (All-Fuel) (Gal.) |
.9 |
Crankcase with Filter (Qts.) |
5 |
Transmission (Qts.) |
40 T |
7-1/2 |
40 S |
6-1/2 |
40 C |
6-1/2 |
Cooling System (Gal.) |
3-1/2 |
Final Drive (Pts.) |
40 C |
1-3/4 |
40 H |
1-1/2 |
40 S |
1-1/2 |
40 T |
4 |
40 U |
2-1/2 |
40 V |
3-1/2 |
40 W |
2-1/2 |
Hydraulic System |
40 C |
9 Qts. (Remote Cyl. System) |
40 C |
11 Qts. (Integral System) |
40 S |
4-1/2 Qts. |
40 T |
5-1/2 Qts. |
40 U |
4-1/2 Qts. |
VALVE DATA |
Valve Spring (Lbs. @ In.) |
39-45 @ 2 |
Valve Length (Intake) (In.) |
5-3/4 |
Valve Length (Exhaust) (In.) |
5-3/4 |
Stem Diameter (Both) (In.) |
.3715/.3725 |
Face Angle (Intake) |
30 degrees |
Face Angle (Exhaust) |
45 degrees |
Head Diameter (Intake) (In.) |
1-13/16 |
Head Diameter (Exhaust) (In.) |
1-9/16 |
Seat Width (Intake) (In.) |
1/8 +/- 1/64-0 |
Seat Width (Exhaust) (In.) |
5/64 +/- 1/64-0 |
Concentricity Tolerance of Valve Seats, Intake & Exhaust |
.002 |
Face of Head to Guide (In.) |
2-3/32 |
Guide Inside Diameter (In.) |
.3745/.3760 |
Recess (Diameter) |
Intake (In.) |
1-3/8 |
Exhaust (In.) |
1-9/32 |
Tappet Adjustments (In.) |
.012 |
Valve Lift |
.372 |
Fit of Stem in Guides |
.002-.0045 |
VALVE TIMING |
Inlet Open |
0 degrees TDC |
Inlet Closes |
50 degrees aBDC |
Exhaust Open |
45 degrees bBDC |
Exhaust Closes |
5 degrees aTDC |
CAMSHAFT |
Bearing Clearance (Front and Rear) |
.0015/.0035 |
End Play |
.003 |
Camshaft Bearing (In.) |
1.812/1.813 |
Camshaft Journals (In.) |
1.8095/1.8105 |
CRANKSHAFT |
End Play (In.) |
.003 to .007 |
Main Bearing Clearance (In.) |
.001 to .0035 |
Main Bearing Diameter (In.) |
2.399/2.4005 |
Main Bearing Journals (In.) |
2.397/2.398 |
Rod Bearing (In.) |
2.500/2.5016 |
Rod Journals (In.) |
2.498/2.499 |
Rod Bearing Clearance (In.) |
.001/.0035 |
PISTONS |
Cylinder Bore Diameter (In.) |
4.000/4.001 |
PISTON DIAMETER AT TOP OF SKIRT |
Parallel to Piston Pin (In.) |
3.985/3.987 |
Right Angles to Piston Pin (In.) |
3.9940/3.9960 |
PISTON DIAMETER AT BOTTOM OF SKIRT |
Parallel to Piston Pin (In.) |
3.987/3.988 |
Right Angles to Piston Pin (In.) |
3.9970/3.9960 |
Piston Pin Bore Diameter (In.) |
1.1880/1.1883 |
Piston Pin Diameter (In.) |
1.1877/1.1879 |
Piston Pin to Piston Pin Bore Clearance (In.) |
.0002/.0007 |
Piston Pin to Piston Pin Bushing Clearance (In.) |
.001/.0004 |
Piston Pin Bushing Diameter (In.) |
1.1883/1.1886 |
PISTON RINGS |
Ring Width |
Upper Compression (In.) |
3/32 |
Center Compression (In.) |
3/32 |
Lower Compression (In.) |
3/32 |
Oil Ring (In.) |
1/4 |
Ring Side Clearance in Groove |
Upper Compression |
.0015/.003 |
Center Compression |
.001/.0025 |
Lower Compression |
.001/.0025 |
Oil Ring |
.001/.0025 |
FLYWHEEL |
Teeth on Ring |
105 |
Spark Mark Index |
25 degrees bTDC |
TOUCH-O-MATIC PUMP |
Output @ 0 Lbs. Pressure |
9.3 |
Output @ 800 Lbs. Pressure |
8.2 |
ROCKER ARM SHAFT |
Diameter (In.) |
.8100/.8105 |
Bushing Diameter (In.) |
.812/.813 |